BC558 TRANSISTOR DATASHEET PDF

0 Comments

DataSheet: PDF icon BCPDF. BC is a general purpose PNP transistor. It is used in switching and amplifier applications. The DC current gain varies in. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. Semiconductor data sheets and/or specifications can and do vary in different applications . BC / BC / BC VCE = -5 V, IC = µA.

Author: Kagul Goltigis
Country: Central African Republic
Language: English (Spanish)
Genre: History
Published (Last): 27 April 2013
Pages: 173
PDF File Size: 13.74 Mb
ePub File Size: 20.20 Mb
ISBN: 203-2-80383-305-7
Downloads: 99207
Price: Free* [*Free Regsitration Required]
Uploader: Kazrajar

The DC current gain varies in range to The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. datasheeet

In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal. BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. BC is a general purpose PNP transistor. Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. BC is used in common emitter configuration for amplifiers.

It is also used as a complement for transistors BC to BC The input signal at base is amplified and taken at the emitter. When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. BC has a gain value of to ; this value determines the amplification capacity of the transistor.

  CARL LEWIS MOT566 PDF

BC Pinout, Configuration, Circuit As Switch & Amplifier

Interface GPS with Arduino. When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. This is known as the biasing. SPI Module of Arduino. Submitted by admin on 26 March This high-density System-in-Package SiP integrates controller, power switches, and support components.

Complete Technical Details can be found in the BC datasheet given at the end of this page. The BC because of this large gain value is normally used to as a audio amplifier.

For amplification applications, the transistor is biased such that it is partly on for all input conditions.

Transistor BC558

When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter. The value of this resistor RB can be calculated using below formulae. TL — Programmable Reference Voltage. Virgin Galactic hc558 Commercial Space Flight. For switching applications, transistor is biased so that it remains fully on if there is a signal at its base.

Skip to main content. What is Web Browser.

Choosing Battery for Robots. Choosing Motor For Robots. It can amplify power, voltage and current at different configurations. Interface SD Card with Arduino. BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Reverse biased when a signal is provided to base pin.

  DEGENERACION ESPINOCEREBELOSA PDF

In the absence of base signal, it gets completely off. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched. Amplifier modules like Audio amplifiers, signal Amplifier etc.

A resistor is always added in series with base pin to limit the base current. Arduino based GPS receiver. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

A Transistors acts as an Amplifier when operating in Active Region. The voltage divider is the commonly used biasing mode. Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration.

As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Reverse Bias, this biasing can be achieved by supplying gransistor required amount of current to the base pin. It is used in switching and amplifier applications.