IEC 60929 PDF

0 Comments

IEC Edition INTERNATIONAL. STANDARD. NORME. INTERNATIONALE. AC and/or DC-supplied electronic control gear for tubular. IEC AC and/or DC-supplied electronic control gear for tubular fluorescent lamps – Performance requirements. International Standard IEC has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee Lamps and related equipment.

Author: Zolor Tokazahn
Country: Burma
Language: English (Spanish)
Genre: Travel
Published (Last): 3 September 2008
Pages: 399
PDF File Size: 1.91 Mb
ePub File Size: 19.77 Mb
ISBN: 821-8-30682-363-3
Downloads: 21557
Price: Free* [*Free Regsitration Required]
Uploader: Juran

In certain applications, different waveforms are used, such as triangular or square waves, audio and radio signals carried on ic wires are also examples of alternating current. You may delete a document from your Alert Profile at any time.

IEC | IEC Webstore | lighting

The sockets are small enough that two can be installed in the space taken by a single Schuko or BS socket, the plugs are slightly larger than the Europlug and provide much more reliable contact.

In common with the Europlug there is a sleeve around the base of the line. NH fuses of sizes 1, 2 and 3, rated A, A and A. The 609229 is a high-power factor rapid start series ballast for two 30—40 W lamps. The standard defines connectors with 3,4 and 5 pins, but a variant with 7 uec is commercially available.

Learn how and when to remove these template messages. March Learn how and when to remove this template message. The key protrudes an additional 3 or 4 mm beyond the shroud diameter, connectors rated at 63 A and A may optionally be equipped with a 6 mm pilot contact.

Electrical ballast — An electrical ballast is a device placed in line with the load to limit the amount of current in an electrical circuit. A common source of DC power is a cell in a flashlight. The smaller end cap has a diameter that varies with the fuse rating, the fixed part of the fuse holder contains a gauge ring, which will accept end caps up to a certain diameter.

  MANUAL DE RECARGA DE MUNICIONES PDF

Standards Catalogue

The AES-3id standard defines a ohm BNC electrical variant of AES3 and this uses the same cabling, patching and infrastructure as analogue or digital video, and is thus common in the broadcast industry. The DALI scene is edited and scene configuration data updated ready to be uploaded into the ballasts.

Uncovered metal envelopes present a risk of shock and should be replaced immediately under extreme precautions by trained personnel.

This gap allows a bit of room above and below a piece of equipment so it may be removed without binding on the adjacent equipment. In some jurisdictions, replacement of the cartridge by unskilled personnel is allowed only for fuses up to a certain maximum rating.

Couplers described under these standards have standardized current and temperature ratings, each type of coupler is identified by a standard sheet number. These commands are used to discover and address DALI ballasts:.

Oh no, there’s been an error

All fuses of different technologies tested to meet IEC standards will have similar time-current characteristics, north American standards call the replaceable element only the fuse. By using this site, you agree to the Terms of Use and Privacy Policy. These are most ice used when a load has its terminal decline when current through the load increases. Whilst this is enabled lec command will be sent every 10 seconds. The protective-earth pins center is offset 3 mm from the point between the line and neutral pin.

  74HC390 DATASHEET PDF

Two IECstyle plugs inserted into wall-mounted sockets. Detachable appliance couplers are used in equipment, measuring instruments, IT environments. If the fuse cartridge is inserted into the socket without the cap, fuseholders may be secured by screws to a panel, attached to bus bars, or mounted on DIN rails.

Several inch racks in ieec professional audio application.

The connectors come in four current ratings 16,32,63 or A per pin, All consist of cylindrical connector pins arranged in a circle, with the earth pin 2 mm larger than the others. Choosing to test alternate ballasts will test every other patched ballast – the remaining ballasts will then be tested once the initial test is complete. The actual operating frequency may deviate from the specified supply frequency.

Please help to improve this article by introducing more precise citations. Please help to improve this article by introducing more precise citations. Init published a multilingual international vocabulary to unify terminology relating to electrical, electronic and this effort continues, and 6092 International Electrotechnical Vocabulary remains an important work in the electrical and electronic industries.

The designation of a size consists of the letter D and a Roman numeral, higher-voltage types rated up to V have increased clearance distances and are longer than lower-voltage-rated fuses.